Warning light Purelux Strobe Side Light, Square

The Purelux Flash Side Light is a very thin position light developed to be mounted with screws on vertical surfaces, e.g. sides, front and rear of the car. With position lights, you can increase the visibility of the vehicle in the desired direction, or in every direction if desired, and they work excellently as a complement to warning lights. The main function of the warning light is to alert those moving around the site to ensure the safety of both workers and others moving around the area. The Purelux Flash Side Light is equipped with 12 different power modes and powerful light that ensures that the vehicle is clearly visible to all passers-by.

The warning light's frame is vibration and corrosion protected, and water and dustproof according to IP67 classification. The lens is also made of almost unbreakable polycarbonate. The operating voltage of 10-30V makes it possible to use the same warning light on cars and vans as well as on heavier vehicles (e.g. trucks, tractors, work machines, etc.). 360° light angle!

Flash Side Light is E-marked and approved for traffic use, and its ECE R65 Class 2 classification means that it is also approved for both day and night use. Flash Side Light has separate power modes adapted for night and day use. During the day, the light shines at full power to provide the best possible visibility, and when used at night, the brightness is lower so as not to risk dazzling drivers, passers-by or other workers around the workplace.

The slim and modern design combined with the very low profile enables a stylish installation on any vehicle. Developed for fixed installation.

ATTENTION! The Purelux Flash Side Light is ECE R65 Class 2 approved, which means it can be used in European traffic! Class 2 means that the luminous flux is sufficient for both night and day use.

NOTE! Also available in a rectangular version: Purelux Recessed Side Light Slim. Both lights can be synchronized together.

Content

• Warning light / Position light Purelux Flash Side Light, Square
• Power cable, 300 mm
• Mounting screws

Technical specification

• Brand and model: Purelux Flash Side Light, Square
• Area of use: Warning/position light
• Operating voltage: 10-30 V
• Power consumption: max. 10W
• Approval:
  • E-marking: ECE R65 Class 2
  • ECE R10, SAE J595 Class 1, California Title 13 Class B
• Protection class: IP67
• 12 different power modes
• Orange light
• Dimensions: 73 x 55 x 14.2 mm (W x D x H)
• Warranty: 24 months

Power modes

• Single Flash ( Day Mode ) / 125 FPM
• Single Flash ( Night Mode ) / 125 FPM
• Single Flash (California Title 13) / 75 FPM
• Double flashing / 125 FPM
• Triple flashing / 125 FPM
• Quadruple flashing / 125 FPM
• Five-fold flashing / 125 FPM
• Combo (single + double blink)
• Combo (single + triple flash)
• Combo (single + quintuple blink)
• Strobe / 600 FPM
• Continuous light (cruise)

Connection manual

ATTENTION! Control box is not included in the package, but the cables are connected as follows:

• Red: Power (+)
• Black: Ground (-)
• Green: Synchronization, change of operating mode, reset
  • Synchronization: select the same operating mode for the lamps to be synchronized, then connect the green wires of the lamps. In this way, the lamps flash in the same rhythm and change operating mode (all together) when the operating mode of a lamp changes.
  • Switch operating mode: Apply power (+) to the green wire and the lamp will switch operating mode. Can be implemented with a circuit breaker (the cable is connected to the battery or other power source, and a pressure switch is inserted in between)
  • Reset: Hold power for more than 5 seconds to reset the lamp to default #1
• White: Alternate sync
  • Alternating synchronization: If the white wires of some of the lights, in addition to the green wire, are connected to the power (+), they are always lit when the others (white wires not connected) are off and vice versa. In this way, the lights can also be synchronized so that they blink at different rates.