Warning light Purelux Strobe Side Light, Slim

The Purelux Flash Side Light is a very thin position light developed to be mounted with screws on vertical surfaces, e.g. sides, front and rear of the car. With position lights, you can increase the visibility of the vehicle in the desired direction, or in every direction if desired, and they work excellently as a complement to warning lights. The main function of the warning light is to alert those moving around the site to ensure the safety of both workers and others moving around the area. The Purelux Flash Side Light is equipped with 12 different power modes and powerful light that ensures that the vehicle is clearly visible to all passers-by.

The warning light's frame is vibration and corrosion protected, and also waterproof and dustproof according to IP67 classification. The lens is also made of almost unbreakable polycarbonate. The operating voltage of 10-30V makes it possible to use the same warning light on cars and vans as well as on heavier vehicles (e.g. trucks, tractors, work machines, etc.). 360° light angle!

Flash Side Light is E-marked and approved for traffic use, and its ECE R65 Class 2 classification means that it is also approved for both day and night use. Flash Side Light has separate power modes adapted for night and day use. During the day, the light shines at full power to provide the best possible visibility, and when used at night, the brightness is lower so as not to risk dazzling drivers, passers-by or other workers around the workplace.

The slim and modern design combined with the very low profile enables a stylish installation on any vehicle. Developed for fixed installation.

ATTENTION! The Purelux Flash Side Light is ECE R65 Class 2 approved, which means it can be used in European traffic! Class 2 means that the luminous flux is sufficient for both night and day use.

NOTE! Also available in a square version: Purelux Flash Side Light Square.

Content

• Warning light / Position light Purelux Flash Side Light, Slim
• Power cable, 300 mm
• Mounting screws

Technical specification

• Brand and model: Purelux Flash Side Light, Slim
• Area of use: Warning/position light
• Operating voltage: 10-30 V
• Power consumption: max. 14W
• Approvals:
  • E-Approval: ECE R65 Class 2
  • EMC: ECE R10, SAE J595 Class 1, California Title 13 Class B
• Protection class: IP67
• 12 different power modes
• Orange light
• Dimensions: 130 x 28 x 8 mm (W x D x H)
• Warranty: 24 months

Operating modes

• Single Flash ( Day Mode ) / 125 FPM
• Single Flash ( Night Mode ) / 125 FPM
• Single Flash (California Title 13) / 75 FPM
• Double flashing / 125 FPM
• Triple flashing / 125 FPM
• Quadruple flashing / 125 FPM
• Five-fold flashing / 125 FPM
• Combo (single + double blink)
• Combo (single + triple flash)
• Combo (single + quintuple blink)
• Strobe / 600 FPM
• Continuous light (cruise)

Quick guide

ATTENTION! Control box is not included in the package, but the cables are connected as follows:

• Red: Power (+)
• Black: Ground (-)
• Green: Change of operating mode, synchronization and reset to first operating mode
  • Switch operating mode: Momentarily energize (connect to positive) the green wire to switch between the different operating modes. Can be implemented with a power switch (the power switch is connected between the battery or other power source and the green cable)
  • Synchronization: Select the same operating mode on the lights you want to synchronize by momentarily energizing the green cable. Then connect the green cables together. In this way, the lamps flash in the same rhythm and change operating mode (all together) when the operating mode of a lamp changes. For alternative synchronization, see below
  • Reset: Hold green wire to positive for more than 5 seconds to reset lamp to operating position #1
• White: Alternate sync
  • Alternative synchronization: First select the same operating mode on all the lights you want to synchronize by momentarily energizing the green cable. Then connect the green cables together. Then connect the white cable to plus on the lights you want to flash alternatively with the remaining lights. This way, the lights with white wire connected to plus will always light up when the others (white wires not connected) are off and vice versa