Warning light bar Purelux Flash 1200 - Panel / 1220 mm / 186W / 12/24V

The Purelux Flash Panel is a very stylish and slim flash light ramp, mainly developed for demanding professional use. The 1220 mm long ramp fits perfectly on both passenger cars and heavier vehicles such as trucks. The main function of the flash light is to alert those moving around the site to ensure the safety of both workers and others moving around the area. The Purelux Flash Panel is equipped with 13 different power modes and powerful light that ensures that the vehicle is clearly visible to all passers-by.

The frame of the flashlight ramp is vibration and corrosion protected, and also waterproof and dustproof according to protection class IP67. The lens is also made of almost unbreakable polycarbonate. The operating voltage of 10-30V makes it possible to use the same flash light on cars and vans as well as on heavier vehicles (e.g. trucks, tractors, work machines, etc.). 360° light angle!

The Flash Panel is E-marked and approved for European traffic use, and its ECE R65 Class 2 classification means that it is also approved for both day and night use. Flash Panel has separate power modes adapted for night and day use. During the day, the ramp shines at full power to provide the best possible visibility, and when used at night, the brightness is lower so as not to risk dazzling drivers, passers-by or other workers around the workplace.

The slim and modern design combined with the very low profile enables a stylish installation on any vehicle. Additionally, the ramp's low profile reduces drag compared to traditional flash light ramps, significantly reducing wind noise. The mounting feet raise the ramp slightly from the level of the substrate, allowing airflow to flow under the panel. In addition, it ensures that the light is clearly visible from the roof of the vehicle. This ramp is designed for fixed installation.

Also available in a larger model: Flash Panel 1400 , as well as smaller models: Flash Panel 800, Flash Panel 400 and Flash Panel 250 models with magnetic attachment and cigarette lighter socket.

Note! You can buy either just the flash bar or a package that includes the flash bar + Purelux Flash Panel Controller , a control panel from which the bar can be adjusted directly in the driver's seat! The control panel does not have a direct connection to the ramp, you have to make the connection yourself.

Content

• Purelux Flash Panel 1220 mm
• Set with mounting feet
• Fixing bolts
• Power cable, 5000 mm

Technical specification

• Brand and model: Purelux Flash Panel 1220
• Area of use: Warning/strobe lights in cars, work machines, etc.
• Operating voltage: 10-30 V
• Valostore's measured max. power (12 V): 186 W
  • Valostore's measured max. power (24 V): 159 W
• Mounting: Mounting feet, Fixing bolts
• Contact: Straight wires, no contact
• Cable length: 500 cm
• Dimensions: 1220 x 36 x 220 mm (Width / Height / Depth)
  • Height with stand: 80 mm
• Weight: 6980 g
• Other: 13 different operating modes, Orange light, Very low profile, 360° light angle
• Protection class: IP67
• Approvals:
  • E-Approval: ECE R65 Class 2
  • ECE R10, CISPR 25 Class 3, SAE J845 Class 1
• Warranty: 24 months
• Importer: Handshake.fi

Power modes

• Simple flashing ( Day mode )
• Simple flashing ( Night mode )
• Double flashing
• Triple flashing (front & back/all)
• Triple flashing (middle/ends/all)
• Combo (single/quad flash)
• Single blink (left/right end)
• Moving light (inside and out)
• Moving blink
• Continuous light (cruise)
• Candle in the middle
• Pill light on the left
• Pill light on the right

Connection manual

ATTENTION! Control box is not included in the package, but the cables are connected as follows: red (+) to power, black (-) to earth and yellow to the separate switch, where power goes. With the yellow, the power modes are checked. The power mode switch must not be depressed at the bottom, but the power mode does not change until the power is interrupted again, e.g. with a switch.

When installing, it is important to remember that some power modes only work on one side of the ramp.